Glycol bearing perylene monoimide based non-fullerene acceptors with increased dielectric permittivity.

Perylene monoimide based electron acceptors have great properties for use in organic solar cells, like thermal stability, strong absorption, and simple synthesis. However, they typically exhibit low values for the dielectric permittivity. This hinders efficient exciton dissociation, limiting the achievable power conversion efficiencies. In this work, we present the synthesis and utilization of two new acceptor-donor-acceptor (A-D-A) molecules, comprising perylene monoimide as electron withdrawing A unit. Oligo ethylene glycol side chain modified carbazole (PMI-[C-OEG]) and fluorene (PMI-[F-OEG]) linkers were used as electron rich D units, respectively. The polar side chains are expected to increase the polarizability of the molecules and, thus, their permittivity according to the Clausius-Mossotti relationship. We found that the incorporation of glycol chains improved the dielectric properties of both materials in comparison to the reference compounds with alkyl chains. The permittivity increased by 18% from 3.17 to 3.75 for the carbazole-based non-fullerene acceptor PMI-[C-OEG] and by 12% from 3.10 to 3.47 for the fluorene-based acceptor PMI-[F-OEG]. The fabricated solar cells revealed power conversion efficiencies of 3.71 ± 0.20% (record 3.92%) with PMI-[C-OEG], and 1.21 ± 0.06% (record 1.51%) with PMI-[F-OEG]. Supplementary Information: The online version contains supplementary material available at 10.1007/s00706-022-02956-2.

Silicon- and Germanium-Functionalized Perylene Diimides: Synthesis, Optoelectronic Properties, and Their Application as Non-fullerene Acceptors in Organic Solar Cells.

Organic solar cells have been continuously studied and developed through the last decades. A major step in their development was the introduction of fused-ring non-fullerene electron acceptors. Yet, beside their high efficiency, they suffer from complex synthesis and stability issues. Perylene-based non-fullerene acceptors, in contrast, can be prepared in only a few steps and display good photochemical and thermal stability. Herein, we introduce four monomeric perylene diimide acceptors obtained in a three-step synthesis. In these molecules, the semimetals silicon and germanium were added in the bay position, on one or both sides of the molecules, resulting in asymmetric and symmetric compounds with a red-shifted absorption compared to unsubstituted perylene diimide. Introducing two germanium atoms improved the crystallinity and charge carrier mobility in the blend with the conjugated polymer PM6. In addition, charge carrier separation is significantly influenced by the high crystallinity of this blend, as shown by transient absorption spectroscopy. As a result, the solar cells reached a power conversion efficiency of 5.38 %, which is one of the highest efficiencies of monomeric perylene diimide-based solar cells recorded to date.

Choose your leaving group: selective photodeprotection in a mixture of pHP-caged compounds by VIPER excitation.

Photocages are light-triggerable molecular moieties that can locally release a pre-determined leaving group (LG). Finding a suitable photocage for a particular application may be challenging, as the choice may be limited by for instance the optical or physicochemical properties of the system. Using more than one photocage to release different LGs in a reaction mixture may even be more difficult. In this work an experimental strategy is presented that allows us to hand-pick the release of different LGs, and to do so in any order. This is achieved by using isotopologue photocage-LG mixtures in combination with ultrafast VIbrationally Promoted Electronic Resonance (VIPER) excitation. The latter provides the required molecular selectivity simply by tuning the wavenumber of the used IR pulses to the resonance of a specific photocage isotopologue, as is demonstrated here for the para-hydroxyphenacyl (pHP) photocage. For spectroscopic convenience, we use isotopologues of the infrared (IR) spectroscopic marker -SCN as different LGs. Especially for applications where fast LG release is required, pHP is found to be an excellent candidate, as free LG formation is observed to occur with a 10 ps lifetime. The devised strategy may open up new complex uncaging applications, where multiple LGs can be formed locally on a short time scale and in any sequence.

A long-lived fluorenyl cation: efficiency booster for uncaging and photobase properties.

The photochemistry of fluorenols has been of special interest for many years. This is because both the fluorenol and the fluorenyl cation are antiaromatic in the ground state due to their 4n π-electrons according to the Hückel rule. The photolysis reaction of various fluorene derivatives takes place via a cation intermediate and is preferred due to its excited state aromaticity. Here we present an extremely long-lived fluorenyl cation and its effects on the uncaging of various leaving groups. We analyze the relationship between uncaging quantum yields of fluorene-based cages and the longevity of their fluorenyl cations with different spectroscopic methods in the steady state and on an ultrafast time scale and find that the uncaging quantum yield rises with the stability of the cation. In contrast to previous reports, the cation can be observed on a time scale of minutes, even in moderately protic solvents as methanol and ethanol. The stability of this cation depends on the dimethylamino-substituents on the fluorene scaffold and the properties of the solvent. In addition, with bis-dimethylamino fluorenol, a photobase is introduced that expands the small group of known photoinduced hydroxide emitters.

Wide-bandgap organic solar cells with a novel perylene-based non-fullerene acceptor enabling open-circuit voltages beyond 1.4 V.

A perylene-based acceptor (PMI-FF-PMI), consisting of two perylene monoimide (PMI) units bridged with a dihydroindeno[1,2-b]fluorene molecule was developed as a potential non-fullerene acceptor (NFA) for organic solar cells (OSCs). The synthesized NFA was combined with the high-performance donor polymer D18 to fabricate efficient OSCs. With an effective bandgap of 2.02 eV, the D18:PMI-FF-PMI blend can be categorized as a wide-bandgap OSC and is an attractive candidate for application as a wide-bandgap sub-cell in all-organic triple-junction solar cell devices. Owing to their large effective bandgap, D18:PMI-FF-PMI solar cells are characterized by an extremely high open-circuit voltage (V OC) of 1.41 V, which to the best of our knowledge is the highest reported value for solution-processed OSCs so far. Despite the exceptionally high V OC of this blend, a comparatively large non-radiative voltage loss (ΔV non-rad OC) of 0.25 V was derived from a detailed voltage loss analysis. Measurements of the electroluminescence quantum yield (ELQY) of the solar cell reveal high ELQY values of ∼0.1%, which contradicts the ELQY values derived from the non-radiative voltage loss (ΔV non-rad OC = 0.25 V, ELQY = 0.0063%). This work should help to raise awareness that (especially for BHJ blends with small ΔHOMO or ΔLUMO offsets) the measured ELQY cannot be straightforwardly used to calculate the ΔV non-rad OC. To avoid any misinterpretation of the non-radiative voltage losses, the presented ELQY discrepancies for the D18:PMI-FF-PMI system should encourage OPV researchers to primarily rely on the ΔV non-rad OC values derived from the presented voltage loss analysis based on EQEPV and J-V measurements.

Phenylene-Bridged Perylene Monoimides as Acceptors for Organic Solar Cells: A Study on the Structure-Property Relationship.

A series of non-fullerene acceptors based on perylene monoimides coupled in the peri position through phenylene linkers were synthesized via Suzuki-coupling reactions. Various substitution patterns were investigated using density functional theory (DFT) calculations in combination with experimental data to elucidate the geometry and their optical and electrochemical properties. Further investigations of the bulk properties with grazing incidence wide angle X-ray scattering (GIWAXS) gave insight into the stacking behavior of the acceptor thin films. Electrochemical and morphological properties correlate with the photovoltaic performance of devices with the polymeric donor PBDB-T and a maximum efficiency of 3.17 % was reached. The study gives detailed information about structure-property relationships of perylene-linker-perylene compounds.

Recent Progress in the Design of Fused-Ring Non-Fullerene Acceptors-Relations between Molecular Structure and Optical, Electronic, and Photovoltaic Properties.

Organic solar cells are on the dawn of the next era. The change of focus toward non-fullerene acceptors has introduced an enormous amount of organic n-type materials and has drastically increased the power conversion efficiencies of organic photovoltaics, now exceeding 18%, a value that was believed to be unreachable some years ago. In this Review, we summarize the recent progress in the design of ladder-type fused-ring non-fullerene acceptors in the years 2018-2020. We thereby concentrate on single layer heterojunction solar cells and omit tandem architectures as well as ternary solar cells. By analyzing more than 700 structures, we highlight the basic design principles and their influence on the optical and electrical structure of the acceptor molecules and review their photovoltaic performance obtained so far. This Review should give an extensive overview of the plenitude of acceptor motifs but will also help to understand which structures and strategies are beneficial for designing materials for highly efficient non-fullerene organic solar cells.

A New Photocage Derived from Fluorene.

Photolabile protecting groups (PPGs or photocages) are increasingly subject to molecular design to meet requirements such as absorbance in the visible spectral range, high molar absorption coefficients, and high quantum yields of leaving group release. Improvements in these properties for the promising 3-diethylaminobenzyl (DEAMb) photocage, the photoactivity of which is based on the Zimmerman meta effect, are reported. Expansion of the aromatic system with a second aromatic ring resulted in improved spectral properties. A systematic trend relating the electronic (π-donor or acceptor) properties of the new aryl substituent and its position in the DEAMb ring to changes in the spectral properties could be observed. Conclusions from the experimental results were supported by computations obtained by using time-dependent DFT. A second generation of DEAMb-based photocages was designed. A rigid linker was introduced to ensure more efficient conjugation of the aromatic ring π systems by limiting rotational freedom. The resulting fluorenol (9-hydroxyfluorene)-based photocages had superior spectral properties to those of simple biphenyl systems. The best uncaging cross section achieved was 5320 m-1 cm-1 (ϵΦ365 ).

Controlling Photochemistry via Isotopomers and IR Pre-excitation.

It is a photochemist's dream to be able to photoinduce a reaction of a specific molecular species in an ensemble of similar but not identical ones. The problem is that similar molecules often exhibit nearly identical UV-Vis absorption spectra, making them difficult or impossible to distinguish or to select spectroscopically. The ultrafast VIPER (VIbrationally Promoted Electronic Resonance) pulse sequence allows to pick a single species for electronic excitation based on its infrared spectrum. The latter usually shows more features, allowing the discrimination between species than the UV-Vis spectrum. Here, we show that it is possible to induce and monitor species-selective photochemistry even for molecules with virtually identical UV-Vis spectra, which is the case for isotopomers. Next to isotope-selective photochemistry in solution, applications to orthogonal photo-uncaging and species-selective spectroscopy and photochemistry in mixtures are within reach.